Cavity oil gun container

Made from an old plastic grease container and an original Shutz underseal can. I also had to shorten the gun pick-up pipe.
knoba - cavity oil gun container

~§~

Prevents rust in: chassis cavities, welded tube cavities, hard to reach internal cavities (internal wheel arch seams, etc.).
knoba - cavity oil gun container

~§~

Threaded connector is epoxied into the lid.
knoba - cavity oil gun container

~§~

I use from a 50:50 mix to 75:25 (oil:white spirit) mix. Soaks into seams, small gap filling, never really dries. Long lasting. Great value. Easy clean-up.
knoba - cavity oil gun container

•••

http://www.homemadetools.net

Steel thumbscrews & jig

What I’m making: M8 wingbolt
knoba - Steel thumbscrews & jig

~§~

Made these tabs to weld onto bolt heads (details in CAD file below)
knoba - Steel thumbscrews & jig

~§~

Replacing these plastic ones (some have broken)
knoba - Steel thumbscrews & jig

~§~

Stock used in making a welding & alignment jig (to help make the wingbolts)
knoba - Steel thumbscrews & jig

~§~

Materials:
1 x 50x50x6 mm (2"x2"x1/4") flat section mild steel
2 x 50x25x3 mm (2"x1"x1/8") equal angle mild steel
1 x 100x14 mm (4"x9/16") hex bar mild steel

All pickled, de-smutted & deburred.
Jig copes with 6mm to 8mm (1/4" to 5/16") bolts

~§~

8mm hole in centre (top side)
knoba - Steel thumbscrews & jig

~§~

Countersunk 90° included angle (underside)
knoba - Steel thumbscrews & jig

~§~

Marked all & drilled (8mm) holes in uprights
knoba - Steel thumbscrews & jig

~§~

Going to plug weld (MIG) through holes to base
knoba - Steel thumbscrews & jig

~§~

Using a wingbolt tab, as a spacer, wrapped in masking tape to add some clearance
knoba - Steel thumbscrews & jig

~§~

Welded
knoba - Steel thumbscrews & jig

~§~

Dressed with angle grinder flapwheel
knoba - Steel thumbscrews & jig

~§~

Marked and sliced through only the angle iron sections
knoba - Steel thumbscrews & jig

~§~

Cleaned up
knoba - Steel thumbscrews & jig

~§~

Nuts, bevelled, threaded & marked. From hex stock
knoba - Steel thumbscrews & jig

~§~

90° included angle
knoba - Steel thumbscrews & jig

~§~

Different threaded nuts
knoba - Steel thumbscrews & jig

~§~

Nuts hold the bolts in good contact & alignment
knoba - Steel thumbscrews & jig

~§~

Tabs are centre marked, drop in with good alignment, ready for welding
knoba - Steel thumbscrews & jig

~§~

What’s in the CAD file
knoba - Steel thumbscrews & jig

~§~

knoba – steel thumbscrews & jig – 2018.dxf

•••

Wired edge dollies

Thanks to billsmetal – youtube. Cut & pickled materials…
knoba - wired edge dollies

~§~

How they will fit together
knoba - wired edge dollies

~§~

Bevelled one edge for easier weld penetration
knoba - wired edge dollies

~§~

Strong, flat heatsink (bench) & clamps to restrict distortion
knoba - wired edge dollies

~§~

Gouged the rear of seam & welded to give homogeneous fusion
knoba - wired edge dollies

~§~

Cleaned up with flap wheel & belt sander.
knoba - wired edge dollies

~§~

Materials:
1 x 20x32x50mm mild steel, Rectangular solid section
1 x 25x38x50mm mild steel, Rectangular solid section
2 x 25x3x50mm mild steel, Flat section
2 x 50x6x50mm mild steel, Flat section

Normalise & harder alloy for upgrades.

~§~

Smaller one here; base is 1/16″ (1.6mm) thick.
knoba - wired edge dollies

~§~

YouTube – Billsmetal

•••

3in1 metal working machine extras

Acquired a bare 3in1 metalwork machine (bends, cuts, rolls).
knoba - Rlc switches

~§~

Machine needed a sturdy base.
knoba - Rlc switches

~§~

Detail in the CAD file below
knoba - Rlc switches

~§~

Chassis finished.
knoba - Rlc switches

~§~

Made a shelf to catch cut sheet from perforated aluminium.
knoba - Rlc switches

~§~

Shelf being trialled.
knoba - Rlc switches

~§~

knoba - Rlc switches

~§~

Machine on base.
knoba - Rlc switches

~§~

I make tool socks for my equipment.
knoba - Rlc switches

~§~

Elastic stitch, eyelet, nylon cord and plastic holder thing.
knoba - Rlc switches

~§~

Keeps tooling with the machine for adjustment / maintenance.
knoba - Rlc switches

~§~

I also make covers for my equipment. Poly cotton.
knoba - Rlc switches

~§~

Detail in the CAD file below
knoba - Rlc switches

~§~

Identical scales on both slip roll adjusters. Machined from ally.
knoba - Rlc switches

~§~

Stamped & levelled thread bottoms so both top settings match.
knoba - Rlc switches

~§~

Added a fence carrier to keep it with the machine.
knoba - Rlc switches

~§~

Ready for work, or storage.
knoba - Rlc switches

~§~

Materials:
1.5m x 50mm x 6mm f/s
6.0m x 50mm x 3mm shs
1m x 2mm x 12mm i/d chs
4 x castors
4 x M10 Bolts x 50mm
12 x M12 Bolts x 70mm
4 x M10 Washers
12 x M12 Washers
4 x M10 Square Weldnuts
12 x M12 Hex Weldnuts
8 x 50mm x 50mm Black Square Plastic End Caps
Paint, Direct to metal, light blue
Polycotton 2m x 1.1m 
Polyester Thread
2.5m Ball chain

~§~</p

Clarke – SBR760 3 in 1 Sheet Metal Machine

knoba – 3in1 metal working machine stand – 2017.dxf

knoba – 3in1 metal working machine cover – 2017.dxf

•••

Spot weld tip shaper

Machined from 22mm o/d silver steel. Top side.
knoba - spot weld tip shaper

~§~

Underside.
knoba - spot weld tip shaper

~§~

Dremeled with diamond burrs.
knoba - spot weld tip shaper

~§~

Held at cherry for 6 to 7 mins.
knoba - spot weld tip shaper

~§~

The gauze, I was trialling, was only good for tempering.
knoba - spot weld tip shaper

~§~

Quenched, here.
knoba - spot weld tip shaper

~§~

Made to fit a thread die holder.
knoba - spot weld tip shaper

~§~

Finished piece. Can be sharpened on either side of cutting edge.
knoba - spot weld tip shaper

~§~

Link to CAD file below.
knoba - spot weld tip shaper

~§~

knoba – spot weld tip shaper – 2018.dxf

•••

Lab tripod

Made from 304 stainless steel.
knoba - lab tripod

~§~

knoba - lab tripod

~§~

It disassembles when not required. The tig’ed nuts are clearance drilled.
knoba - lab tripod

~§~

Silicon feet good to approx. 200°c.
knoba - lab tripod

~§~

In action.
knoba - lab tripod

~§~

CAD file link below.
knoba - lab tripod

~§~

knoba – lab tripod – 2017.dxf

•••

Jewellers bench plate

Plate is 5mm x 200mm, spot welded clamp bracket is 2.2mm, mild steel.
knoba - jewellers bench plate - 01

~§~

Clamp is 6mm x 25mm, m8 threaded bar, turned piece on end
knoba - jewellers bench plate - 02

~§~

Finish is sulphuric acid pickling & satin black cellulose
knoba - jewellers bench plate - 03

~§~

Good stability, very solid.
knoba - jewellers bench plate - 04

~§~

knoba – Jewellers Bench – 2016.dxf (CAD file link below)
knoba - jewellers bench plate

~§~

knoba – Jewellers Bench – 2016.dxf

•••

Box Spanner

46mm (across flats) low torque, box spanner, for restricted access on long threads.
knoba - box spanner - 01

~§~

Welded bead around perimeter to add strength.
knoba - box spanner - 02

~§~

Body is scaffold pole, 60% penetration on hex seam to avoid internal excess metal…
knoba - box spanner - 03

•••

Saab 9-3 2002 Steering Issue

Investigated “clicking noise” on steering.

Vehicle is in very good condition.

The o/s steering rack mount. Severe corrosion and cracks. I have to take that bracket section off!
knoba - saab 9-3 2002 steering issue - 01

~§~

The yellow markings indicate places where the bracket was hanging on. The entire left side (cracked, top to bottom), lower end & 2 spot welds (by the stud fixing holes), of this (2.4mm plate) are supposed to be a structural part of the vehicle.
knoba - saab 9-3 2002 steering issue - 02

~§~

Lower end of the bulkhead mounting bracket has completely rusted away.
knoba - saab 9-3 2002 steering issue - 03

~§~

View of bulkhead corrosion (engine bay side) after bracket was removed. Bracket is source of corrosion initiator.
knoba - saab 9-3 2002 steering issue - 04

~§~

Chasing the rust caused by this bracket; inside o/s wheel arch…
knoba - saab 9-3 2002 steering issue - 05

~§~

Chasing the rust caused by this bracket; interior o/s floor well. The tyre can be seen through wheel arch (on right) & the main chassis rail (centre of hole)…
knoba - saab 9-3 2002 steering issue - 06

~§~

Why did it fail?

Closer inspection, of the bracket tear, reveals a saw tooth edge. Suggesting repeated side impacts on the wheels, possibly caused from parking up curbs and such…
knoba - saab 9-3 2002 steering issue - 07

~§~

Even with the flimsy fixings remaining on the bracket, it doesn’t account for the amount of movement available to create that tear. Further investigation resolves it; crack in bulkhead…
knoba - saab 9-3 2002 steering issue - 08

~§~

Cut out all rust. Make & weld in new sections (upper floor pan, lower bulkhead, wheel arch). Modify & re-attach bracket (extend lower section, weld to main chassis rail). Weld bulkhead crack from interior side. Dress, seam seal, prime, paint & underseal.

~§~

BOC – Industrial gases

Murex – Welding equipment

•••

Ford transit mt75 gearbox quickchange

Original gear lever assembly
knoba - transit mt75 gearbox quickchange

~§~

knoba - transit mt75 gearbox quickchange

~§~

knoba - transit mt75 gearbox quickchange

~§~

knoba - transit mt75 gearbox quickchange

~§~

Pin and spherical part (some chrome alloy) may have been brazed
knoba - transit mt75 gearbox quickchange

~§~

Welded & machined assembly adds an extra 20mm to the selector end
knoba - transit mt75 gearbox quickchange

~§~

knoba - transit mt75 gearbox quickchange

~§~

knoba - transit mt75 gearbox quickchange

~§~

Gearbox housing spacer cast and machined from aluminium
knoba - transit mt75 gearbox quickchange

~§~

knoba - transit mt75 gearbox quickchange

~§~

Completed assembly reduces top-end throws from 6″, to 4″ ~ 33% reduction.
knoba - transit mt75 gearbox quickchange

~§~

knoba – metal casting furnace

knoba – ball turning fixture for lathe

Wiki – Lever

•••

Welding turn table

Made from a garden table & a Haag-Streit Bern Keratometer
knoba - welding turn table

~§~

The base unit already had a superb height adjustment mechanism…
knoba - welding turn table

~§~

The lower platter can turn independently of the the top one, be removed or be used as a rest…
knoba - welding turn table

~§~

It disassembles easily because it has to stay outside.
knoba - welding turn table

~§~

Some lovely engineering and workmanship went into this…
knoba - welding turn table

~§~

knoba - welding turn table

~§~

There was a lot of brass machining on this project
knoba - welding turn table

~§~

knoba - welding turn table

~§~

Fortunately, I didn’t have to make the wire…
knoba - welding turn table

~§~

Specifics & details all in the cad file…
knoba - welding turn table

~§~

knoba – Welding turn table – 2015.dxf (link below)
knoba - welding turn table

~§~

Haag-streit – Medical technology group

knoba – Welding turn table – 2015.dxf

•••

Window grills

To protect a pair of period glazed windows from ball impact strikes.
knoba - window mesh

~§~

Low profile, near hinge side, allows window to open without impediment.
knoba - window mesh

~§~

Upright frame sections take loading from the arched mesh and dissipate shocks.
knoba - window mesh

~§~

Frames will be fitted with only the top laterals fixed (m5 countersunks).
knoba - window mesh

~§~

knoba - window mesh

~§~

Balling achieved by melting ends with TIG.
knoba - window mesh

~§~

knoba - window mesh

~§~

Single sided adhesive closed cell foam tape (20mm x 1.5mm).
knoba - window mesh

~§~

knoba - window mesh

~§~

Homemade tucking fork used to shape the open wire ends.
knoba - window mesh

~§~

Wooden buck used to profile the weldmesh.
knoba - window mesh

~§~

knoba – Window Mesh – 2015.dxf (link below)
knoba - window mesh

~§~

knoba – Window Mesh – 2015.dxf

Parker Steel – 20 X 3mm Mild Steel Flat

Parker Steel – 2″ X 2″ X 10G GALV Weldmesh Sheet

Ebay – Black Single Sided Foam Tape Closed Cell 20mm Wide x 1.5mm Thick

Ebay – m5 Countersunk Pozi Machine Screws

Screwfix – No Nonsense Timber Decking Oil Clear 5Ltr

•••

Garden Arch

Made from fencing panels (bent by kerf cutting laterals).
knoba - garden arch

~§~

Supported by an external welded steel framework (30mm x 8mm x 30 meters).
knoba - garden arch

~§~

3m wide x 3m high (3.6m from bottom of steps).
knoba - garden arch
Now home to a sweet flowering Jasmine.

~§~

Theflowerexpert.com – Jasmine

Parker Steel – 30 X 8mm Mild Steel Flat

•••

Magnetic welding clamp

Made from an old Amstrad CB mag-mount car aerial
knoba - magnetic welding clamp

~§~

knoba - magnetic welding clamp

~§~

knoba - magnetic welding clamp

~§~

Recycle – Ilovefreegle.org

Forum – Homemadetools.net

Forum – Mig-welding.co.uk

•••

Tig filler rod dispensers

Made from 50mm x 3m Waste pipe & 50mm Socket plugs.

Tig filler rod dispensers

~§~

TIG trolley was specifically designed to use these tubes.

Tig filler rod dispensers

~§~

BES – Water Waste Solvent Weld Pipe & Fittings

knoba – TIG trolley

•••

BBQ

Bbq from free-cycled gas tanks (propane & helium).

BBQ

~§~

BBQ

~§~

BBQ

~§~

BBQ

~§~

BBQ

~§~

ilovefreegle.org

•••

Pneumatic Planishing Hammer

Finished tool
Pneumatic Planishing Hammer

~§~

Lever from beloved Rover P5 Gearstick
Pneumatic Planishing Hammer

~§~

Hammer & dolly set from work hardened 304 austenitic stainless steel
Pneumatic Planishing Hammer

~§~

Machined clamp tig welded to tube
Pneumatic Planishing Hammer

~§~

Support casings from sliding bolt assemblies
Pneumatic Planishing Hammer

~§~

Locking swivel stand
Pneumatic Planishing Hammer

~§~

Folds away for easy storage
Pneumatic Planishing Hammer

~§~

Clarke – CAT95 Air Hammer Kit

Hammerite – Direct to Rust Metal Paint

Norgren – X3048202 Inline Valves – Manual/Mechanical

Amazon – Ancol Rubber Dog Balls

•••

Bench grinder station

New bench grinder station

~§~

New bench grinder station

~§~

New bench grinder station

~§~

Diamond wheel…
New bench grinder station

~§~

Record – RSBG8 8″ Bench Grinder with 40mm Whitestone

Draper – 200 x 19mm Crimped Steel Wire Brush

Tooled-up.com – Zenith Taper Spindle Left Hand 16mm

Vertex – Quartz Hanlogen Lamp VHL-20FT

Parker Steel – Black Carbon Steel Flats

Hammerite – Direct to Rust Metal Paint

3M – Convolute Deburring Wheels

Ebay – AIM Tools – 150x35x32x5x3mm Diamond Grinding Flat Conical Wheel

•••

MIG torch mini welding visor

Made from 304 stainless steel & shade #9 glass for restricted area access (vehicle welding)
MIG torch mini welding visor

~§~

Removable & serviceable
MIG torch mini welding visor

~§~

MIG torch mini welding visor

~§~

MIG torch mini welding visor

~§~

MIG torch mini welding visor

~§~

Forum – mig-welding.co.uk

•••

Wardrobe in stainless steel

Wardrobe in 304 stainless steel
Wardrobe in stainless steel

~§~

-FEET-

Parts for the castor mounts
Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

-SHOE RACK-

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

-UPRIGHTS-

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

-HANGER RAIL-

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

-TOP MESH-

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

-ASSEMBLY-

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

Wardrobe in stainless steel

~§~

knoba – Wardrobe – 2009.dxf

knoba – Angle grinder pigtail for polishing

knoba – Dewalt DW872 TCT metal chop saw mods

knoba – V Blocks

knoba – Doming plate

Forum – mig-welding.co.uk

Starrett – HSS Bi Metal Hole Saw Kits

Cibo – Finit-Easy

Cibo – Finimaster Pro

Parker steel – Stainless Steel Metric Flats

Parker steel – Stainless Steel Metric Rounds

Metalgeek.com – Tube Coping Calculator

•••

Dewalt DW 320 radial arm saw table

Radial arm saw table

~§~

Radial arm saw table

~§~

Radial arm saw table

~§~

Radial arm saw table

~§~

Radial arm saw table

~§~

Radial arm saw table

~§~

Radial arm saw table

~§~

Hammerite – Direct to Rust Metal Paint

Parkersteel – Carbon Steels Square Hollow Section

Castors-Online – 75mm Swivel Castor with Single bolt fixing

knoba – Radial Arm Saw Stand – 2011.dxf

•••

Garage / workshop doors with Stainless steel hardware

Garage / workshop doors with 304 Stainless steel hardware
Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

Garage / workshop doors with Stainless steel hardware

~§~

knoba – Sliding Dead Bolt – 2009.dxf

Cibo – Finit-Easy

Cibo – Finimaster Pro

Parker steel – Stainless Steel Metric Flats

Wenban-smith – Hardwoods

Wenban-smith – Softwoods

•••

Aerial in Stainless steel

Aerial in 304 Stainless steel
Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

MIG welded with Easb 0.8 308lsi stainless wire & BOC Stainsheild
Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

Aerial in Stainless steel

~§~

knoba – Angle grinder pigtail for polishing

knoba – V Blocks

knoba – Doming plate

Makita – 9565PCV 125mm Variable speed angle grinder

•••

TIG Trolley

TIG Trolley

~§~

TIG Trolley

~§~

TIG Trolley

~§~

Quick release
TIG Trolley

~§~

TIG Trolley

~§~

TIG Trolley

~§~

knoba - TIG Trolley

~§~

knoba – V Blocks

Forum – mig-welding.co.uk

B&Q – Hand Trolley HT2022

Hammerite – Direct to Rust Metal Paint

•••

Metal horse for metal working

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

Metal horse for metal working

~§~

knoba – Metal Horse – 2010.dxf

Forum – mig-welding.co.uk

Hammerite – Direct to Rust Metal Paint

Wilton – 1550 High-Visibility Safety 5” Vise with Swivel Base

•••

Wood turning fixture & rests

Lathe wood turning fixture & polished 304 stainless steel rests
Wood turning fixture & rests

~§~

Wood turning fixture & rests

~§~

Wood turning fixture & rests

~§~

Wood turning fixture & rests

~§~

Extended rest.
Wood turning fixture & rests

~§~

Wood turning fixture & rests

~§~

knoba – Radius keepers

knoba – Spur drive

Homemadetools.net

•••

Stainless steel TV Stand

Polished 304 Stainless steel & oak flatscreen TV Stand
Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

Stainless steel & oak TV Stand

~§~

knoba – Tv Stand – 2008.dxf

Forum – mig-welding.co.uk

Colron – Refined Finishing Wax

Parker steel – Stainless Steel Metric Rounds

Cibo – Finit-Easy

Cibo – Finimaster Pro

Metalgeek.com – Tube Coping Calculator

•••

Railing post caps

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Railing post caps

~§~

Dewalt – DW872 TCT metal chopsaw

Barneswelding.com – Jancy JANMCBL14SS Stainless Steel Cuttng Blade

•••

Keats plate

Keats plate

~§~

For holding round stock (jaw can be reversed for larger diameters).
Keats plate

~§~

knoba – dividing plate for pillar drill

•••

Driveway gates

Driveway gates

~§~

Driveway gates

~§~

Driveway gates

~§~

knoba – Ball turning fixture for lathe

Hammerite – Direct to Rust Metal Paint

Parkersteel – Carbon Steels Equal Angles

•••

Pressure pot sandblaster

Currently using crushed glass & tungsten nozzles.
pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

pressure pot sandblaster

~§~

Think: carburetor…
pressure pot sandblaster

~§~

knoba – Sand blasting enclosure

Parkersteel – Carbon Steels Square Hollow Section

Hammerite – Direct to Rust Metal Paint

Ebay – Blastitclean TUNGSTEN CARBIDE SANDBLASTING NOZZLE 3MM

Ebay – CENTURYWISE 25kg RECYCLED GLASS

•••